Orion-system VCM-X E-BUS Component Manual do Utilizador Página 55
- Página / 128
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
VCM-X Component & Systems Wiring
VCM-X Expansion Module Wiring
55
AO5
AO4
GND
Modular Cable
Connect To VCM-X E-BUS Controller
Modular Cable
Connect To Next Expansion
Board (When Used)
24 VAC
GND
10 VA Minimum Power
Required For
VCM-X Expansion Module
WARNING!!
Observe Polarity! All boards must be wired with GND-to-GND and 24VAC-to-24VAC. Failure
to observe polarity will result in damage to one or more of the boards. Expansion Modules
must be wired in such a way that the expansion modules and the controller are always
powered together. Loss of power to the expansion module will cause the controller to become
inoperative until power is restored to the expansion module.
Return Air Bypass
Damper Actuator
(0-10 VDC)
Return Air
Damper Actuator
(0-10 VDC)
Belimo Actuator Wiring
Shown. Consult Factory
For Other Manufacturer
Wiring Instructions.
3Y1
3Y1
2 +
2 +
1 COM
1 COM
VCM-X
Expansion
Module
RELAY CONTACT
RATING IS 1 AMP
MAX @ 24 VAC
RELAY 2
RELAY 1
RELAY 3
RELAY 4
RELAY
COMMON
I2C
EXPANSION
I2C
EXPANSION
AO1 = BUILDING PRESSURE CONTROL VFD OR
DAMPER ACTUATOR (0-10 OR 2-10 VDC)
= MODULATING HEATING SIGNAL
(0-10 VDC OR 2-10 VDC)
= MODULATING COOLING/DIGITAL SCROLL
SIGNAL (0-10 VDC, 2-10 VDC OR 1.5-5 VDC)
= RETURN AIR DAMPER ACTUATOR
(0-10 VDC)
= RETURN AIR BYPASS DAMPER ACTUATOR
(0-10 VDC)
= GROUND FOR ANALOG OUTPUTS
= GROUND FOR ANALOG OUTPUTS
AO2
AO3
AO4
AO5
GND
GND
BI1 = HOOD ON - N.O. INPUT
BI2
BI3
BI4
BI5
BI6
BI7
BI8
= DIRTY FILTER - N.O. INPUT
= PROOF OF FLOW - N.O. INPUT
= REMOTE FORCED OCCUPIED - N.O. INPUT
= REMOTE FORCED HEATING - N.O. INPUT
= REMOTE FORCED COOLING - N.O. INPUT
= SMOKE DETECTOR - N.C. INPUT
= REMOTE DEHUMIDIFICATION - N.O. INPUT
ANALOG INPUT
JUMPER SETTINGS
MUST BE SET AS
SHOWN FOR
PROPER
OPERATION
24 VAC POWER ONLY
WARNING! POLARITY MUST BE
OBSERVED OR THE BOARD
WILL BE DAMAGED
www.orioncontrols.com
AI1
AI2
AI3
AI4
THERM
THERM
THERM
THERM
4-20mA
4-20mA
4-20mA
4-20mA
0-10V
0-10V
0-10V
0-10V
0-5V
0-5V
0-5V
0-5V
ANALOG INPUT
JUMPER
SETTINGS
RELAY 1 = RELAY 3 =
RELAY 2 = RELAY 4 =
IT IS SUGGESTED
THAT YOU WRITE THE
DESCRIPTION OF
THE RELAY OUTPUTS
YOU ARE USING IN
THE BOXES
PROVIDED ABOVE
WITH A PERMANENT
MARKER (SHARPIE®)
WattMaster Label
#LB102034-01
NOTE:
ALL BINARY INPUTS MUST BE 24 VAC ONLY.
AI1 = OUTDOOR AIR RH SENSOR (0-5 VDC)
AI2
AI3
AI4
GND
GND
= INDOOR AIR RH SENSOR (0-5 VDC)
= CO2 (0-10 VDC)
= BUILDING STATIC PRESSURE (0-5 VDC)
= GROUND FOR ANALOG INPUTS
= GROUND FOR ANALOG INPUTS
+V
SIG
GND
PR OUT
GND
SUCTION PRESSURE
TRANSDUCER CONNECTION
FOR HVAC UNITS WITHOUT
DIGITAL COMPRESSOR
TO VCM-X INPUT
TERMINALS AI5 & GND
OE333-23-EM-A VCM-X EXPANSION MODULE
VCM
WARNING
OBSERVE
POLARITY
RELAY CONTACT
RATING IS 1 AMP
MAX @ 24 VAC
RELAY 2
RELAY 1
RELAY 3
RELAY 4
RELAY
COMMON
I2C
EXPANSION
I2C
EXPANSION
AO1 = BUILDING PRESSURE CONTROL VFD OR
DAMPER ACTUATOR (0-10 OR 2-10 VDC)
= MODULATING HEATING SIGNAL
(0-10 VDC OR 2-10 VDC)
= MODULATING COOLING/DIGITAL SCROLL
SIGNAL (0-10 VDC, 2-10 VDC OR 1.5-5 VDC)
= RETURN AIR DAMPER ACTUATOR
(0-10 VDC)
= RETURN AIR BYPASS DAMPER ACTUATOR
(0-10 VDC)
= GROUND FOR ANALOG OUTPUTS
= GROUND FOR ANALOG OUTPUTS
AO2
AO3
AO4
AO5
GND
GND
ANALOG INPUT
JUMPER SETTINGS
MUST BE SET AS
SHOWN FOR
PROPER
OPERATION
24 VAC POWER
ONLY
WARNING!
POLARITY
MUST BE
OBSERVED OR
THE BOARD
WILL BE
DAMAGED
AI1
AI2
AI3
AI4
THERM
THERM
THERM
THERM
4-20mA
4-20mA
4-20mA
4-20mA
0-10V
0-10V
0-10V
0-10V
0-5V
0-5V
0-5V
0-5V
ANALOG INPUT
JUMPER
SETTINGS
RELAY 1 = RELAY 3 =
RELAY 2 = RELAY 4 =
IT IS SUGGESTED
THAT YOU WRITE THE
DESCRIPTION OF
THE RELAY OUTPUTS
YOU ARE USING IN
THE BOXES
PROVIDED ABOVE
WITH A PERMANENT
MARKER (SHARPIE®)
WattMaster Label
#LB102034-01-A
Rev.: 1L
NOTE:
ALL BINARY INPUTS MUST BE 24 VAC ONLY.
+V
SIG
GND
PR OUT
GND
SUCTION PRESSURE
TRANSDUCER CONNECTION
FOR HVAC UNITS WITHOUT
DIGITAL COMPRESSOR
TO VCM-X INPUT
TERMINALS AI5 & GND
BI1 = EMERGENCY SHUTDOWN - N.C. INPUT
= DIRTY FILTER - N.O. INPUT
= PROOF OF FLOW - N.O. INPUT
= REMOTE FORCED OCCUPIED - N.O. INPUT
= REMOTE FORCED HEATING - N.O. INPUT
= REMOTE FORCED COOLING - N.O. INPUT
= HOOD ON - N.O. INPUT
= REMOTE DEHUMIDIFICATION - N.O. INPUT
BI2
BI3
BI4
BI5
BI6
BI7
BI8
www.aaon.com
www.orioncontrols.com
VCM-X Expansion Module
Orion No.:OE333-23-EM
AAON No.:
R69190
AI1 = OUTDOOR AIR RH SENSOR (0-5 VDC)
AI2
A3
AI4
GND
GND
= INDOOR AIR RH SENSOR (0-5 VDC)
= ECONOMIZER FEEDBACK
= BUILDING STATIC PRESSURE (0-5 VDC)
= GROUND FOR ANALOG INPUTS
= GROUND FOR ANALOG INPUTS
I
FILENAME
DATE:
S. Olson
DESCRIPTION:
PAGE
BY:
JOB NAME
OVCMX-RA-BYP-Wr-1B.cdr
1 of 1
05/15/15
VCM-X Expansion Module
Return Air Bypass Wiring
Return Air Bypass
Figure 36: Return Air Bypass Wiring
- VCM-X E-BUS Component & 1
- Table of Contents 2
- Commissioning 5
- Systems Overview 6
- System Types 6
- Wiring Considerations 8
- Wire & Transformer Sizing 9
- Orion VCM-X System 9
- WARNING! 10
- Stand-Alone 11
- System Installation 12
- Networked Single Loop 13
- Networked Multiple Loop 17
- System Commissioning 20
- Overview 20
- System Configurations 21
- Typical Stand Alone System 22
- Interconnected System 23
- Networked Single Loop System 24
- Note: CommLink Must Be Set 29
- For Multiple Loop Operation 29
- Connect To Modular 30
- I/O Connectors 30
- Located On Back 30
- Of The System Manager 30
- VCM-X E-BUS 31
- VCM-X E-BUS Controller Wiring 32
- Main Controller Wiring 32
- Main Controller Addressing 33
- Sensor Wiring 34
- Duct-Mounted CO 35
- VCM-X E-BUS Controller 37
- Caution: 39
- VCM-X Expansion 41
- Expansion Module Wiring 41
- VCM-X Expansion Module Wiring 42
- Input Wiring 42
- Output Wiring 43
- VCM-X Expansion Module 46
- OVCMX-BinInput-4BIN-1A.CDR 47
- OA Humidity Sensor 48
- Space Humidity Sensor 49
- RA Humidity Sensor 50
- OVCMX-BldgPr-Wr-1A.CDR 52
- Building Pressure Control 52
- Damper Actuator 52
- Modular Cable 53
- Connect To VCM-X Controller 53
- Connect To Next Expansion 53
- Board (When Used) 53
- Modulating Cooling Device 54
- (Configurable) 54
- Expansion 55
- OVCMX-12RelayWire-1A.CDR 56
- GTC116 Series, GreenTrol 57
- MicroTrans 57
- Modular & Non-Modular 59
- VAV/Zone Controller 59
- Diagrams 59
- OE210-02, OE211-02, OE212-02 60
- OE217-00 / OE217-01 60
- Digital Room Sensor 60
- Slaved Zone Wiring 68
- Communication Devices 69
- OE392-12 Modular System 71
- Manager SD 71
- Back of Front Cover 71
- OE392-10 75
- System Manager TS II 75
- Back View 75
- IP-ModInstall1A.CDR 77
- CommLink 5 79
- Communication Loop Wiring 81
- CAUTION! 83
- Add-On Devices Diagrams 85
- Add-On Devices 86
- GPC-X Controller Wiring 87
- GPC-XP Controller Wiring 89
- GPC-XP CommLink Setting 91
- OE332-23-GPC-XP 91
- GBD-X Controller - CO 92
- Applications Wiring 92
- Applications Wiring (Cont’d) 93
- Module Wiring 97
- & Connections 97
- OE370-23-HP1C 98
- One Condenser 98
- Head Pressure Module 98
- OE370-23-HP2C2 99
- Two Condenser 99
- Head Pressure II Module 99
- OE370-23-FD-A 100
- Full Digital Module 100
- OE370-23-DD-C 101
- Dual Digital Module 101
- Controller Wiring 102
- AAON MODGAS-X Wiring 103
- (OE377-26-00060) 104
- MODGAS-XWR CONTROLLER 104
- MHGRV-X CONTROLLER 107
- (OE377-26-00059) 107
- OE334-26-WSHP-X2 108
- Water Source 108
- Heat Pump X2 Module 108
- AAON PREHEAT-X Wiring 110
- AAON MODGAS II Wiring 111
- AAON MHGRV II Controller 112
- Only Required When More Than 113
- Valves Are Needed 113
- MHGRV III Controller 113
- Miscellaneous Diagrams 115
- & Technical Information 115
- Modular Room Sensor Wiring 116
- EPROM Chip Locations 117
- EPROM Chip Locations (Cont’d) 118
- SD Memory Card Update 121
- E-BUS Modules 122
- OE275-01 Suction Pressure 126
- Refrigerant 126
Manuais e produtos relacionados com Hardware Orion-system VCM-X E-BUS Component
Hardware Orion-system MHGRV-X Manual do Utilizador
(26 páginas)
(26 páginas)
Hardware Orion-system MODGAS-X Manual do Utilizador
(28 páginas)
(28 páginas)
Hardware Orion-system PREHEAT-X Manual do Utilizador
(28 páginas)
(28 páginas)
Hardware Orion-system MHGRV II Manual do Utilizador
(12 páginas)
(12 páginas)
Hardware Orion-system MODGAS II Manual do Utilizador
(22 páginas)
(22 páginas)
Apple CP-X255 manuales
Manuales del propietario y guías del usuario para Proyectores Apple CP-X255.
Ofrecemos 5 manuales en pdf Apple CP-X255 para descargar gratis por tipos de documentos: Manual de usuario, Información técnica, Instrucciones de operaciones
Comentários a estes Manuais