Orion-system Full Digital Module Manual do Utilizador Página 11

  • Descarregar
  • Adicionar aos meus manuais
  • Imprimir
Vista de página 10
Technical Guide
Full Digital Module
11
Modes of Operation
NOTE: See Unit Con gurations Chart on page 10 for more
information about compressor staging.
Digital Stage 1 / Digital Stage 2
On units with two Digital Scroll Compressors, the rst compressor (A1)
will be designated as Digital Stage 1 and the second compressor (A2)
will be designated as Digital Stage 2.
On units with four Digital Scroll Compressors, there may be instances
where compressor numbers on the module do not correlate with the
mechanical compressors’ numbers. Therefore, Digital Stage 1 refers to
the rst set of Digital Scroll Compressors (A1/B1) that will stage on
together and Digital Stage 2 refers to the second set of Digital Scroll
Compressors (A2/B2) that will stage on together. Please refer to AAON’s
wiring diagram for speci c wiring of the unit.
Off Mode
The Full Digital Module will be in the Off Mode when no signal is
being received from the VCM-X Modular series controller to run the
compressors.
Cooling Mode
When a Cool Signal is received, the Full Digital Module will go into
Cooling Mode. At this point, Compressor A1 (and B1*) will energize and
Digital Stage 1 Analog Output will modulate as necessary to maintain
the Supply Air Temperature at the Active Supply Air Setpoint that is
broadcast from the VCM-X Modular series controller.
When Digital Stage 1 reaches 100%, a stage up timer is started. If Digital
Stage 1 stays at 100% for the Stage Up timer, Compressor A2 (and B2*)
will energize and both Digital Stage 1 and Digital Stage 2 outputs will
go to 50% and begin to modulate together.
If both systems are energized and they go below 30% and the Supply Air
is below the Supply Air Setpoint by the Cooling Stage Window value,
the stage down timer is started. If the systems remain below 30% for
the duration of the stage down timer, Digital Stage 2 will deactivate and
Digital Stage 1 will go to 60%. Digital Stage 1 will stage down if it is
at 0% for the duration of the stage down timer.
* If con gured for 4 modulating compressors.
Heat Pump Heating Mode (Air to Air)
Heating Mode works the same as Cooling Mode except the Reversing
Valve is switched and the sequence is opposite. Compressors modulate
up when below the Heating Supply Air Setpoint and modulate down
when above the setpoint.
Dehumidi cation Mode
In Dehumidi cation Mode, compressors will be controlled to maintain
the Suction Pressure Temperature Setpoint. Digital Stage 1—Com-
pressor A1 (and B1*) will modulate up to 100% before Digital Stage
2—Compressor A2 (and B2*) can be energized. When Digital Stage 2
is energized, Digital Stage 1 will be locked at 100%.
* If con gured for 4 modulating compressors.
Defrost Mode
In Defrost Mode, if only Digital Stage 1 is energized, it will go to 100%
and the reversing valve will deactivate. If both Digital Stage 1 & Digital
Stage 2 are energized, they will both go to 100% and the reversing valve
will be deactivated. The duration for Defrost Mode is determined by the
VCM-X Modular series controller.
NOTE: Defrost Mode is only available if a One Condenser or
Two Condenser Head Pressure Module is installed.
Staging Delays
Staging Delays minimum run times and minimum off times are sent
from the VCM-X Modular series controller.
Revised: 12/16/13
Vista de página 10
1 2 ... 6 7 8 9 10 11 12 13 14 15 16

Comentários a estes Manuais

Sem comentários

Apple CP-X255 manuales

Manuales del propietario y guías del usuario para Proyectores Apple CP-X255.
Ofrecemos 5 manuales en pdf Apple CP-X255 para descargar gratis por tipos de documentos: Manual de usuario, Información técnica, Instrucciones de operaciones


Apple CP-X255 Manual de usuario (108 paginas)


Marca: Apple | Categoria: Projectors | Tamaño: 7.73 MB |

 

Tabla de contenidos

CP-S245/CP-X255

1

关于包装箱中的物品

3

否则会导致烫伤。

4

钟,让投影机充分冷却。仅可在这些异常情况下按下重启开关。

5

对于机型 CP-X255

8

对于机型 CP-S

8

调节投影机的脚撑

9

用 RGB IN OUT 开关按

12

钮选择 RGB IN2(如果

12

未按下该按钮,则选择

12

RGB IN2)。

12

连接 VCR/DVD 播放机的实例

13

连接到显示器 (输出)

13

连接到扬声器带放大器 (输出)

13

电源打开时,将发射强烈光线。请勿直视投影机的镜头或通风口。

17

PAGE DOWN

18

选择输入信号(续)

19

请用 USB 电缆将投影机的 USB 端子连接到计算机。

23

► 鼠标 / 键盘控制的错误操作有可能造成设备的故障。

23

RESET 按钮

24

ENTER 按钮

24

用简易菜单可以执行下表中显示的项目。

25

用投影机或遥控器上的光标按钮 ▲/▼ 选择项目。

25

接着参照下表进行操作。

25

伽马 [自定义 1]

27

用输入菜单可以执行下表中显示的项目。

32

用投影机或遥控器上的光标按钮 ▲/▼ 选择项目,然后按投

32

继续。接着参照下表进行操作。

32

用设置菜单,可以选择下表中所列的选项。

34

用屏幕菜单可以执行下表中显示的项目。

35

38

192. 168. 254

40

255. 255. 0

40

    ,  +   :否 ,   :是

41

请参阅另册网络功能的有关章节。

42

通知事项 •

44

空气过滤器(续)

46

更换内置时钟的电池

47

联系您的经销商或服务公司。

49

与经销商或服务公司联系。

50

投影机内部过热时,出于安全目的,电源自动关闭并且指示灯也

51

容易误认为是故障的现象

52

容易误认为是故障的现象(续)

53

请联系您的经销商或服务公司。他们会告诉您适用的保修条款。

55

本规格有可能因为技术改进等原因不经预告而发生变更。

55

249 mm100 mm

56

仅限于 CP-S245/X255

57

使用网络功能之前…

59

通过互联网浏览器设置和控制投影机

60

下表为管理者 ID、用户 ID 和密码的出厂缺省设定。

61

Network Information

63

Network Settings

64

Port Settings

65

Mail Settings

66

Alert Settings

67

Alert Settings(续)

68

点击 [Apply] 键保存设置。

71

Schedule Settings

72

Date/Time Settings

74

Date/Time Settings(续)

75

Security Settings

76

Projector Control

77

Projector Control(续)

78

Projector Status

79

Network Restart

80

通过电子邮件发出失败和警告报警

81

通过 SNMP 操纵投影机

83

通过程式控制投影机

84

日期 / 时间设置

85

通过网络进行命令控制

89

命令控制设置(续)

90

Initial set signals

95

Connection to the ports

96

RJ-45 jack

98

RS-232C Communication

99

Instruction Manual

108

DZ-GX3100E/DZ-BX37E/DZ-BX35E

108

DZ-GX3300E/DZ-GX3200E

108





Más productos y manuales para Proyectores Apple

Modelos Tipo de documento
LP 650 Manual de usuario   GY-HM650 New Product News (2 pg, April 2012) [en] , 2 paginas